Friday, 30 November 2012

WEEK 10


Title:  Designing the casing of the project.

                This week I working on the selecting the material for the base and also the box to place all the circuit, battery and sources for the project. For avoiding problems occur when placing heavy wind turbine and large solar panel, L steel will be used to build the frame and thin layer of plywood to cover the L steel frame in this project. L steel will be cutting according to measurement by using grinder and for plywood saw will be used.For combine the L steel bolt and nut will be used. To touch up the project, lastly it will be spray with black color. Below is figure of material that be used:

pic of plywood

pic of L steel


WEEK 9



Title:  Source storage
                For source storage, I will be used A rechargeable battery, storage battery, or accumulator is a type of electrical battery. It comprises one or more electrochemical cells, and is a type of energy accumulator. It is known as a secondary cell because its electrochemical reactions are electrically reversible. Rechargeable batteries come in many different shapes and sizes, ranging from button cells to megawatt systems connected to stabilize an electrical distribution network. Several different combinations of chemicals are commonly used, including: lead–acid,nickel cadmium (NiCd), nickel metal hydride (NiMH), lithium ion (Li-ion), and lithium ion polymer (Li-ion polymer).
Rechargeable batteries have lower total cost of use and environmental impact than disposable batteries. Some rechargeable battery types are available in the same sizes as disposable types. Rechargeable batteries have higher initial cost, but can be recharged very cheaply and used many times.






top view rechargeable battery

front view rechargeable battery










WEEK 8



Title of activity: Design PCB board for charge controller circuit 


After the conformation on the circuit I start to design the circuit by using Dip trace software for the main circuit and for LCD circuit. After design I go to the printing shop to print the circuit layout to the transparent paper, after that I attach and stick the circuit layout on the transparent paper to the PCB board. Then I use iron to make the ink from the transparent paper stick to the PCB board.

After the ink properly sticks to the PCB board I need to check if any broken connection of the line circuit layout and need to repair by using marker. After satisfied with the connection I start to etching the PCB board. After etching I need to check the connection again to make sure no broken line and no connection are connect each other. After several of etching that satisfied me I start drill the hole by using driller to put the component on the circuit.

schematic diagram

PCB layout

drilling PCB for components

circuit charge controller




WEEK 7

Title of the activity: Designing the hump for piezo films


For the piezo films, its will be place at the hump. When the car go trough to the hump it will be pressing the piezo films. When it be press it will generates electricity. So I will design small scale of hump to place a piezo film to show how will the piezo films will be function and wasy for me to demo in the presentation.  I do by cutting half of milo tin to create the hump. Below is figure of hump for the piezo films.


hump with piezo


WEEK 6


Title of the activity: Designing the PCB layout for combination sources

For the combination circuit, it will need four inputs for four sources and will be one output before go to boost circuit. For this circuit, it just a simple circuit. So I don’t need to use software to draw the layout line. I only use permanent marker ink before do the etching. The component that is use  only t-block and diode. Below is figure of combination circuit:

top view of combination circuit






WEEK 5


Title of the activity : Designing the blade of the turbine.

            To design the blade to move the rotor of alternator to generated electricity, the light material will be used for wind turbine called “aluminium" was used. The criteria of using this aluminium is because it easy to design, cheap, and light. Figure below shows the picture of the blade.


blade be welding to the shaft



spraying the blade



WEEK 4


Title of activity: PCB board testing for boost circuit 



            For this week, the circuit board for boost circuit will be testing to know if the circuit can get the output as the simulation at the proteus software. The methods are when the supply from 9v from battery give supply to the boost circuit, the output should get almost two times higher from the voltage from battery. Figure below shows the PCB board of boost with the components.

top view of boost circuit



                                                            bottom view of boost circuit 



Video of testing boost circuit: